--- System Configuration Dialog ---
Continue with
configuration dialog? [yes/no]: no
Press RETURN to get
started!
Router>en
Router#conf t
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#hostname
R1
R1(config)#int se0/0/0
R1(config-if)#ip add
10.0.0.1 255.255.255.252
R1(config-if)#clock rate
64000
R1(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/0, changed state to down
R1(config-if)#exit
R1(config)#int se0/0/1
R1(config-if)#ip add
60.0.0.2 255.255.255.252
R1(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/1, changed state to down
R1(config-if)#ex
R1(config)#int se0/1/0
R1(config-if)#ip add
40.0.0.1 255.255.255.252
R1(config-if)#clock rate
64000
R1(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/1/0, changed state to down
R1(config-if)#ex
R1(config)#int fa0/0
R1(config-if)#ip add
172.25.16.1 255.255.0.0
R1(config-if)#no shut
R1(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line
protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#ex
R1(config)#router eigrp
100
R1(config-router)#network
10.0.0.0 0.0.0.3
R1(config-router)#network
40.0.0.0 0.0.0.3
R1(config-router)#network
60.0.0.0 0.0.0.3
R1(config-router)#network
172.25.16.0 0.0.255.255
R1(config-router)#exit
R1(config)#router rip
R1(config-router)#network
10.0.0.0
R1(config-router)#network
40.0.0.0
R1(config-router)#network
60.0.0.0
R1(config-router)#network
172.25.16.0
R1(config-router)#exit
R1(config)#router ospf
200
R1(config-router)#network
10.0.0.0 0.0.0.3 area 0
R1(config-router)#network
40.0.0.0 0.0.0.3 area 0
R1(config-router)#network
60.0.0.0 0.0.0.3 area 0
R1(config-router)#network
172.25.16.0 0.0.255.255 area 0
R1(config-router)#exit
R1(config)#^Z
R1#
%SYS-5-CONFIG_I:
Configured from console by console
^Z
R1#copy running-config
startup-config
Destination filename
[startup-config]?
Building configuration...
[OK]
R1#
l
Konfigurasi Router2
--- System Configuration
Dialog ---
Continue with
configuration dialog? [yes/no]: no
Press RETURN to get
started!
Router>en
Router#conf t
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#hostname
R2
R2(config)#int se0/0/1
R2(config-if)#ip add
20.0.0.1 255.255.255.252
R2(config-if)#clock rate
64000
R2(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/1, changed state to down
R2(config-if)#ex
R2(config)#int se0/0/0
R2(config-if)#ip add
10.0.0.2 255.255.255.252
R2(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/0, changed state to up
R2(config-if)#ex
R2(config)#router eigrp
%LINEPROTO-5-UPDOWN: Line
protocol on Interface Serial0/0/0, changed state to up
% Incomplete command.
R2(config)#router eigrp
100
R2(config-router)#network
10.0.0.0 0.0.0.3
R2(config-router)#
%DUAL-5-NBRCHANGE:
IP-EIGRP 100: Neighbor 10.0.0.1 (Serial0/0/0) is up: new adjacency
R2(config-router)#network
20.0.0.0 0.0.0.3
R2(config-router)#ex
R2(config)#ex
R2#
%SYS-5-CONFIG_I:
Configured from console by console
R2#
R2#copy running-config
startup-config
Destination filename
[startup-config]?
Building configuration...
[OK]
R2#
l Konfigurasi
Router3
--- System Configuration
Dialog ---
Continue with
configuration dialog? [yes/no]: no
Press RETURN to get
started!
Router>en
Router#conf t
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#hostname
R3
R3(config)#int s0/0/0
R3(config-if)#ip add
40.0.0.2 255.255.255.252
R3(config-if)#no shut
R3(config-if)#
%LINK-5-CHANGED:
Interface Serial0/0/0, changed state to up
ex
R3(config)#int s0/0/1
R3(config-if)#ip add
50.0.0.1 255.255.255.252
R3(config-if)#clock rate
64000
R3(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/1, changed state to down
R3(config-if)#ex
R3(config)#router rip
R3(config-router)#network
40.0.0.0
R3(config-router)#network
50.0.0.0
R3(config-router)#ex
R3(config)#ex
%SYS-5-CONFIG_I:
Configured from console by console
R3#copy run
R3#copy running-config
start
R3#copy running-config
startup-config
Destination filename
[startup-config]?
Building configuration...
[OK]
R3#
l Konfigurasi
Router4
--- System Configuration
Dialog ---
Continue with
configuration dialog? [yes/no]: no
Press RETURN to get
started!
Router>en
Router#conf t
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#hostname
R4
R4(config)#int s0/0/0
R4(config-if)#ip add
60.0.0.1 255.255.255.252
R4(config-if)#clock rate
64000
R4(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/0, changed state to up
R4(config-if)#ex
R4(config)#int s0/0/1
R4(config-if)#ip add
70.0.0.2 255.255.255.252
R4(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/1, changed state to down
R4(config-if)#ex
R4(config)#router ospf
200
R4(config-router)#network
60.0.0.0 0.0.0.3 area 0
R4(config-router)#network
70.0.0.0 0.0.0.3 area 0
R4(config-router)#ex
R4(config)#^Z
R4#
%SYS-5-CONFIG_I:
Configured from console by console
^Z
R4#copy running-config star
R4#copy running-config
startup-config
Destination filename
[startup-config]?
Building configuration...
[OK]
R4#
l Konfigurasi
Router5
--- System Configuration
Dialog ---
Continue with
configuration dialog? [yes/no]: no
Press RETURN to get
started!
Router>en
Router#conf t
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#hostname
R5
R5(config)#int s0/0/1
R5(config-if)#ip add
70.0.0.1 255.255.255.252
R5(config-if)#clock rate
64000
R5(config-if)#no shut
%LINK-5-CHANGED: Interface
Serial0/0/1, changed state to up
R5(config-if)#ex
R5(config)#int s0/1/0
R5(config-if)#ip add
20.0.0.2 255.255.255.252
R5(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/1/0, changed state to up
R5(config-if)#ex
R5(config)#int s0/0/0
%LINEPROTO-5-UPDOWN: Line
protocol on Interface Serial0/1/0, changed state to up
R5(config-if)#ip add
50.0.0.2 255.255.255.252
R5(config-if)#no shut
%LINK-5-CHANGED:
Interface Serial0/0/0, changed state to up
R5(config-if)#ex
R5(config)#router eigrp
100
R5(config-router)#net
R5(config-router)#network
20.0.0.0 0.0.0.3
R5(config-router)#network
50.0.0.0 0.0.0.3
R5(config-router)#network
70.0.0.0 0.0.0.3
R5(config-router)#network
200.10.10.0 0.0.255.255
R5(config-router)#ex
R5(config)#router rip
R5(config-router)#network
20.0.0.0
R5(config-router)#network
50.0.0.0
R5(config-router)#network
70.0.0.0
R5(config-router)#network
200.10.10.0
R5(config-router)#ex
R5(config)#router ospf
200
R5(config-router)#network
20.0.0.0 0.0.0.3 area 0
R5(config-router)#network
50.0.0.0 0.0.0.3 area 0
R5(config-router)#network
70.0.0.0 0.0.0.3 area 0
R5(config-router)#network
200.10.10.0 0.0.255.255 area 0
R5(config-router)#ex
R5(config)#int fa0/0
R5(config-if)#ip add
200.10.10.1 255.255.255.0
R5(config-if)#no shut
R5(config-if)#ex
R5(config)#^Z
R5#
%SYS-5-CONFIG_I:
Configured from console by console
^Z
R5#copy run
R5#copy running-config
star
R5#copy running-config
startup-config
Destination filename
[startup-config]?
Building configuration...
[OK]
R5#
- Setelah itu
kita coba test apakah pc 1 dengan pc 0 terkoneksi atau tidak *seperti berikut*
- Dan jika berhasil maka tampilan akan seperti berikut
SEKIAN TUTORIAL DARI SAYA TENTANG
Konfigurasi Dynamic Routing RIP - EIGRP -OSPF